APRS Track Direct

My position About ☰

reset

HS1ZHY-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS1ZHY-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1790669004	1 Pkt	-31 dBm	15.59 V
1790668079	2 Pkt	-30 dBm	15.93 V
1790667155	2 Pkt	-31 dBm	16.02 V
1790666231	3 Pkt	-30 dBm	15.2 V
1790665306	1 Pkt	-32 dBm	15.63 V
1790664382	1 Pkt	-32 dBm	13.62 V
1790663457	0 Pkt	-32 dBm	15.46 V
1790662533	2 Pkt	-32 dBm	15.77 V
1790661608	1 Pkt	-31 dBm	15.93 V
1790660684	3 Pkt	-32 dBm	15.5 V
1790659759	1 Pkt	-32 dBm	15.93 V
1790658834	3 Pkt	-32 dBm	13.8 V
1790657910	5 Pkt	-33 dBm	16 V
1790656985	1 Pkt	-30 dBm	15.71 V
1790656061	2 Pkt	-30 dBm	15.59 V
1790655136	1 Pkt	-31 dBm	15.5 V
1790654212	2 Pkt	-32 dBm	15.79 V
1790653287	0 Pkt	-30 dBm	15.71 V
1790652363	0 Pkt	-33 dBm	15.38 V
1790651438	0 Pkt	-30 dBm	15.87 V
1790650514	4 Pkt	-31 dBm	15.01 V
1790649589	2 Pkt	-31 dBm	15.85 V
1790648664	2 Pkt	-33 dBm	15.91 V
1790647740	0 Pkt	-31 dBm	15.57 V
1790646815	1 Pkt	-32 dBm	15.61 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)