This is the latest recevied telemetry packets stored in our database for station/object XE1DGC-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Value1* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1790637409 | 141 | 30 | 999 | 339 | 289 |
| 1790633906 | 141 | 30 | 999 | 338 | 274 |
| 1790630403 | 141 | 30 | 999 | 339 | 291 |
| 1790626901 | 141 | 30 | 999 | 329 | 279 |
| 1790623399 | 141 | 29 | 999 | 329 | 278 |
| 1790619896 | 141 | 29 | 999 | 328 | 275 |
| 1790616394 | 141 | 29 | 999 | 354 | 293 |
| 1790612892 | 141 | 29 | 999 | 356 | 297 |
| 1790609389 | 141 | 29 | 999 | 343 | 281 |
| 1790605887 | 141 | 29 | 999 | 346 | 281 |
| 1790602385 | 141 | 29 | 999 | 358 | 299 |
| 1790598882 | 141 | 29 | 999 | 358 | 300 |
| 1790595380 | 141 | 29 | 999 | 355 | 296 |
| 1790591878 | 141 | 29 | 999 | 357 | 298 |
| 1790588375 | 141 | 29 | 999 | 351 | 291 |
| 1790584873 | 141 | 29 | 999 | 341 | 278 |
| 1790581370 | 141 | 29 | 999 | 349 | 287 |
| 1790577868 | 141 | 30 | 999 | 340 | 277 |
| 1790574366 | 141 | 30 | 999 | 344 | 281 |
| 1790570863 | 141 | 30 | 999 | 352 | 292 |
| 1790567361 | 141 | 30 | 999 | 342 | 280 |
| 1790563859 | 141 | 30 | 999 | 342 | 290 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)