APRS Track Direct

My position About ☰

reset

W8MAI-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W8MAI-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U1*	Temp*	Rx1h*	Dg1h*
1758232083	13.4 Volt	25 C	540 Pkt	180 Pkt
1758232080	13.4 Volt	25 C	540 Pkt	180 Pkt
1758230281	13.4 Volt	25 C	550 Pkt	200 Pkt
1758230280	13.4 Volt	25 C	550 Pkt	200 Pkt
1758228486	13.4 Volt	24.5 C	580 Pkt	210 Pkt
1758228480	13.4 Volt	24.5 C	580 Pkt	210 Pkt
1758226681	13.4 Volt	24.5 C	560 Pkt	190 Pkt
1758226680	13.4 Volt	24.5 C	560 Pkt	190 Pkt
1758224882	13.4 Volt	25.5 C	540 Pkt	180 Pkt
1758224880	13.4 Volt	25.5 C	540 Pkt	180 Pkt
1758223081	13.4 Volt	24.5 C	540 Pkt	170 Pkt
1758223080	13.4 Volt	24.5 C	540 Pkt	170 Pkt
1758221282	13.4 Volt	25 C	560 Pkt	180 Pkt
1758221280	13.4 Volt	25 C	560 Pkt	180 Pkt
1758219481	13.4 Volt	24.5 C	580 Pkt	170 Pkt
1758219480	13.4 Volt	24.5 C	580 Pkt	170 Pkt
1758217682	13.4 Volt	24.5 C	590 Pkt	160 Pkt
1758217681	13.4 Volt	24.5 C	590 Pkt	160 Pkt
1758215886	13.4 Volt	24.5 C	650 Pkt	180 Pkt
1758215881	13.4 Volt	24.5 C	650 Pkt	180 Pkt
1758214082	13.4 Volt	24.5 C	680 Pkt	200 Pkt
1758214081	13.4 Volt	24.5 C	680 Pkt	200 Pkt
1758212281	13.4 Volt	24.5 C	680 Pkt	190 Pkt
1758210488	13.4 Volt	23.5 C	700 Pkt	170 Pkt
1758210481	13.4 Volt	23.5 C	700 Pkt	170 Pkt

*Used Equation Coefficients:

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)