APRS Track Direct

My position About ☰

reset

BV1EV-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV1EV-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1786723702	36 C	0 p	0 p	42 p
1786722502	36.6 C	0 p	2 p	42 p
1786721302	35.5 C	0 p	2 p	42 p
1786720102	35.2 C	2 p	2 p	42 p
1786718902	36.9 C	0 p	0 p	40 p
1786717703	37.2 C	0 p	0 p	40 p
1786716502	36.8 C	0 p	0 p	40 p
1786715302	36.8 C	0 p	0 p	40 p
1786714102	38.9 C	0 p	0 p	40 p
1786712902	39 C	0 p	4 p	40 p
1786711702	40 C	0 p	7 p	40 p
1786710502	41.9 C	4 p	7 p	40 p
1786709302	41.7 C	3 p	3 p	36 p
1786708102	42 C	0 p	0 p	33 p
1786706903	42.9 C	0 p	0 p	33 p
1786705702	41.8 C	0 p	7 p	33 p
1786704502	41.7 C	0 p	7 p	33 p
1786703302	42.4 C	7 p	7 p	33 p
1786702102	42.3 C	0 p	0 p	32 p
1786700902	42.2 C	0 p	0 p	32 p
1786699702	42.2 C	0 p	0 p	32 p
1786698502	42.3 C	0 p	0 p	32 p
1786697303	41.3 C	0 p	0 p	32 p
1786696103	42.4 C	0 p	0 p	32 p
1786694902	41.5 C	0 p	0 p	32 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)