APRS Track Direct

My position About ☰

reset

BV1EV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV1EV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790662807	43.5 C	3 p	9 p	246 p
1790661607	43.6 C	2 p	9 p	246 p
1790660406	43.5 C	4 p	10 p	247 p
1790659206	44.2 C	3 p	10 p	247 p
1790658006	43.1 C	3 p	10 p	247 p
1790656806	42.6 C	4 p	10 p	247 p
1790655606	42.5 C	3 p	10 p	247 p
1790654406	43 C	3 p	10 p	247 p
1790653206	42.2 C	4 p	10 p	247 p
1790652007	42.6 C	3 p	10 p	247 p
1790650807	42 C	3 p	10 p	247 p
1790649607	40.9 C	4 p	10 p	247 p
1790648407	41.1 C	3 p	13 p	247 p
1790647207	39.6 C	3 p	13 p	247 p
1790646007	39.4 C	7 p	13 p	247 p
1790644807	39.4 C	3 p	10 p	247 p
1790643614	38.9 C	3 p	10 p	247 p
1790642406	37.3 C	4 p	10 p	247 p
1790641206	37.4 C	3 p	10 p	247 p
1790640007	36.5 C	3 p	10 p	247 p
1790638807	36.9 C	4 p	9 p	247 p
1790637607	36.6 C	3 p	9 p	247 p
1790636407	36.6 C	2 p	8 p	247 p
1790635207	36.3 C	4 p	9 p	248 p
1790634006	36.3 C	2 p	9 p	248 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)