APRS Track Direct

My position About ☰

reset

YD1OCG-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD1OCG-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CTemp*	CLoad*	CFreq*	RFree*	DTemp*
1790657328	49 C	16 %	2416 MHz	45 %	40 C
1790657027	50 C	59 %	2416 MHz	45 %	40 C
1790656728	49 C	27 %	2416 MHz	45 %	40 C
1790656428	49 C	13 %	2416 MHz	45 %	40 C
1790656128	49 C	49 %	2417 MHz	45 %	40 C
1790655828	49 C	16 %	2417 MHz	45 %	40 C
1790655527	49 C	22 %	2416 MHz	45 %	40 C
1790655228	48 C	17 %	2416 MHz	45 %	40 C
1790654928	48 C	18 %	2416 MHz	45 %	40 C
1790654627	48 C	17 %	2416 MHz	45 %	40 C
1790654328	48 C	38 %	2416 MHz	45 %	40 C
1790654028	48 C	18 %	2417 MHz	45 %	40 C
1790653727	48 C	18 %	2416 MHz	45 %	40 C
1790653428	48 C	26 %	2417 MHz	45 %	40 C
1790653127	48 C	17 %	2416 MHz	45 %	40 C
1790652827	48 C	18 %	2416 MHz	45 %	40 C
1790652527	48 C	11 %	2416 MHz	45 %	40 C
1790652228	47 C	18 %	2416 MHz	45 %	40 C
1790651928	47 C	17 %	2416 MHz	45 %	40 C
1790651628	47 C	15 %	2416 MHz	45 %	40 C
1790651328	47 C	16 %	2416 MHz	45 %	40 C
1790651027	47 C	19 %	2416 MHz	45 %	40 C
1790650728	47 C	16 %	2417 MHz	45 %	40 C
1790650428	47 C	16 %	2416 MHz	45 %	40 C
1790650128	46 C	19 %	2416 MHz	45 %	40 C

*Used Equation Coefficients:

CTemp: 0, 1, 0

CLoad: 0, 1, 0

CFreq: 0, 1, 0

RFree: 0, 1, 0

DTemp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)