APRS Track Direct

My position About ☰

reset

NO2C-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NO2C-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1782502435	250 Pkts	244 Pkts	15 C
1782498835	244 Pkts	238 Pkts	15 C
1782495235	252 Pkts	245 Pkts	14 C
1782491635	330 Pkts	323 Pkts	14 C
1782488035	278 Pkts	273 Pkts	14 C
1782484435	208 Pkts	205 Pkts	14 C
1782480835	127 Pkts	127 Pkts	14 C
1782477235	139 Pkts	137 Pkts	15 C
1782473635	254 Pkts	247 Pkts	15 C
1782470035	247 Pkts	240 Pkts	15 C
1782466435	194 Pkts	190 Pkts	15 C
1782462835	228 Pkts	222 Pkts	14 C
1782459235	271 Pkts	263 Pkts	15 C
1782455635	174 Pkts	168 Pkts	15 C
1782452035	269 Pkts	264 Pkts	15 C
1782448435	280 Pkts	277 Pkts	15 C
1782444835	158 Pkts	152 Pkts	15 C
1782441235	126 Pkts	124 Pkts	15 C
1782437635	180 Pkts	180 Pkts	15 C
1782434035	405 Pkts	395 Pkts	15 C
1782430435	436 Pkts	431 Pkts	16 C
1782426835	385 Pkts	379 Pkts	15 C
1782423235	335 Pkts	327 Pkts	15 C
1782419635	358 Pkts	349 Pkts	15 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)