APRS Track Direct

My position About ☰

reset

SHLDR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SHLDR. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Temp*	Temp*
1790650406	12.68 Volt	11.5 C	-62 C
1790648305	12.75 Volt	12 C	-62 C
1790646205	12.75 Volt	12 C	-62 C
1790644105	12.83 Volt	12.5 C	-62 C
1790642006	12.98 Volt	12.5 C	-62 C
1790639906	13.2 Volt	13 C	-62 C
1790637806	13.43 Volt	13 C	-62 C
1790635706	13.5 Volt	13 C	-62 C
1790633606	13.2 Volt	13 C	-62 C
1790631506	13.43 Volt	13 C	-62 C
1790629406	13.28 Volt	13.5 C	-62 C
1790627306	13.35 Volt	13.5 C	-62 C
1790625206	13.35 Volt	13.5 C	-62 C
1790623106	13.28 Volt	13 C	-62 C
1790621008	13.35 Volt	13 C	-62 C
1790618906	13.35 Volt	12.5 C	-62 C
1790616806	13.35 Volt	12.5 C	-62 C
1790614706	12.75 Volt	12.5 C	-62 C
1790612606	12.9 Volt	12.5 C	-62 C
1790610506	12.6 Volt	12 C	-62 C
1790608407	12.68 Volt	12 C	-62 C
1790606307	12.6 Volt	12 C	-62 C
1790604207	12.6 Volt	12 C	-62 C
1790602107	12.6 Volt	12.5 C	-62 C
1790600007	12.6 Volt	12.5 C	-62 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -67

Temp: 0, 0.5, -62

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)