APRS Track Direct

My position About ☰

reset

OE3XWJ-92 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3XWJ-92. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	60 Wasserstand*	65 Wassertemperatur*	50 Batteriespannung*
1768362347	24.6 cm	29 °C	13.2 V
1768361147	24.6 cm	29 °C	13.2 V
1768353045	24.6 cm	29 °C	13.2 V
1768352445	24.6 cm	29 °C	13.2 V
1768351878	24.6 cm	29 °C	13.2 V
1768349743	24.6 cm	29 °C	13.2 V
1768349143	24.6 cm	29 °C	0 V
1768348548	24.6 cm	29 °C	13.2 V
1768348324	24.6 cm	29 °C	13.2 V
1768347944	24.6 cm	29 °C	13.2 V
1768343441	24.6 cm	29 °C	13.2 V
1768341641	24.7 cm	29 °C	13.2 V
1768336611	24.7 cm	28 °C	0 V
1768335945	24.7 cm	28 °C	13.2 V
1768335718	24.7 cm	28 °C	13.2 V
1768335345	24.7 cm	28 °C	13.2 V
1768331746	24.8 cm	28 °C	13.2 V
1768330556	24.8 cm	28 °C	0 V
1768330253	24.8 cm	28 °C	13.2 V
1768328146	24.8 cm	28 °C	13.2 V
1768327872	24.8 cm	28 °C	13.2 V
1768327244	24.8 cm	28 °C	13.2 V
1768326644	24.8 cm	28 °C	13.2 V
1768325757	24.8 cm	28 °C	13.2 V
1768325449	24.8 cm	28 °C	13.2 V

*Used Equation Coefficients:

60 Wasserstand: 0, 1, 0

65 Wassertemperatur: 0, 1, 0

50 Batteriespannung: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)