APRS Track Direct

My position About ☰

reset

N3XKU-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N3XKU-7. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Eff1h*
1836274578	13.51 Volt	530 Pkt	72 Pcnt
1836274577	13.51 Volt	530 Pkt	72 Pcnt
1765984441	13.27 Volt	140 Pkt	52 Pcnt
1765982640	13.35 Volt	180 Pkt	55 Pcnt
1765980838	13.11 Volt	220 Pkt	55 Pcnt
1765979036	13.35 Volt	250 Pkt	62 Pcnt
1765977235	13.04 Volt	320 Pkt	71 Pcnt
1765975433	13.27 Volt	350 Pkt	65 Pcnt
1765973631	13.43 Volt	310 Pkt	57 Pcnt
1765971830	13.43 Volt	350 Pkt	57 Pcnt
1765970028	13.19 Volt	400 Pkt	61 Pcnt
1765968226	13.19 Volt	390 Pkt	62 Pcnt
1765966424	13.35 Volt	390 Pkt	63 Pcnt
1765964623	13.35 Volt	390 Pkt	63 Pcnt
1765962821	13.35 Volt	400 Pkt	64 Pcnt
1765961019	13.27 Volt	420 Pkt	59 Pcnt
1765959218	13.35 Volt	450 Pkt	54 Pcnt
1765957416	13.35 Volt	430 Pkt	59 Pcnt
1765955614	13.59 Volt	380 Pkt	66 Pcnt
1765953812	13.51 Volt	340 Pkt	68 Pcnt
1765952011	13.27 Volt	360 Pkt	67 Pcnt
1765950209	13.43 Volt	360 Pkt	65 Pcnt
1765948407	13.59 Volt	230 Pkt	56 Pcnt
1765946606	13.51 Volt	130 Pkt	44 Pcnt
1765944804	13.59 Volt	200 Pkt	65 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Value3: 0, 0, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)