APRS Track Direct

My position About ☰

reset

HS4ADH-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4ADH-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1764279276	1 Pkt	-51 dBm	0.06 V
1764277466	0 Pkt	-51 dBm	0.06 V
1764275584	1 Pkt	-50 dBm	0.06 V
1764273774	1 Pkt	-50 dBm	0.06 V
1764271964	0 Pkt	-51 dBm	0.1 V
1764270154	2 Pkt	-50 dBm	0.08 V
1764268344	0 Pkt	-50 dBm	0.08 V
1764266534	0 Pkt	-51 dBm	0.1 V
1764264724	1 Pkt	-51 dBm	0.08 V
1764262914	2 Pkt	-51 dBm	0.08 V
1764261104	5 Pkt	-51 dBm	0.08 V
1764259294	0 Pkt	-52 dBm	0.12 V
1764257410	12 Pkt	-52 dBm	0.12 V
1764255600	14 Pkt	-50 dBm	0.06 V
1764253790	22 Pkt	-51 dBm	0.04 V
1764251980	24 Pkt	-51 dBm	0.06 V
1764250170	20 Pkt	-51 dBm	0.08 V
1764248360	18 Pkt	-51 dBm	0.06 V
1764246550	17 Pkt	-51 dBm	0.02 V
1764244740	13 Pkt	-49 dBm	0.08 V
1764242930	16 Pkt	-49 dBm	0.06 V
1764241120	1 Pkt	-50 dBm	0.1 V
1764239238	11 Pkt	-51 dBm	0.1 V
1764237428	7 Pkt	-51 dBm	0.1 V
1764235618	7 Pkt	-51 dBm	0.1 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)