APRS Track Direct

My position About ☰

reset

E25IHH-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E25IHH-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1764279256	1 Pkt	-41 dBm	0 V
1764277446	0 Pkt	-41 dBm	0.08 V
1764275562	0 Pkt	-41 dBm	0.02 V
1764273752	1 Pkt	-43 dBm	0.06 V
1764271942	0 Pkt	-41 dBm	0.02 V
1764270132	2 Pkt	-42 dBm	0.02 V
1764268322	1 Pkt	-39 dBm	0.02 V
1764266512	0 Pkt	-42 dBm	0.02 V
1764264702	0 Pkt	-37 dBm	0 V
1764262892	2 Pkt	-41 dBm	0 V
1764261082	5 Pkt	-41 dBm	0.06 V
1764259272	0 Pkt	-35 dBm	0 V
1764257390	14 Pkt	-41 dBm	0.04 V
1764255580	14 Pkt	-42 dBm	0 V
1764253770	21 Pkt	-40 dBm	0.02 V
1764251960	25 Pkt	-43 dBm	0 V
1764250150	20 Pkt	-35 dBm	0 V
1764248340	19 Pkt	-37 dBm	0.04 V
1764246530	18 Pkt	-43 dBm	0 V
1764244721	14 Pkt	-41 dBm	0 V
1764242911	12 Pkt	-39 dBm	0.08 V
1764241101	1 Pkt	-43 dBm	0.04 V
1764239218	11 Pkt	-42 dBm	0.02 V
1764237409	7 Pkt	-38 dBm	0.04 V
1764235599	8 Pkt	-38 dBm	0 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)