APRS Track Direct

My position About ☰

reset

LU4FM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU4FM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274844	0 Pkt	-73 dBm	11.92 V
1774163985	0 Pkt	-75 dBm	11.92 V
1774162163	0 Pkt	-74 dBm	11.81 V
1774160341	0 Pkt	-73 dBm	11.92 V
1774158519	0 Pkt	-74 dBm	11.92 V
1774156697	1 Pkt	-74 dBm	11.92 V
1774154875	0 Pkt	-74 dBm	11.92 V
1774153053	0 Pkt	-74 dBm	11.81 V
1774151231	0 Pkt	-72 dBm	11.92 V
1774149409	2 Pkt	-74 dBm	11.92 V
1774147587	0 Pkt	-73 dBm	11.92 V
1774145765	0 Pkt	-73 dBm	11.92 V
1774143943	0 Pkt	-73 dBm	11.92 V
1774142051	0 Pkt	-71 dBm	11.92 V
1774140229	0 Pkt	-71 dBm	11.92 V
1774138407	2 Pkt	-70 dBm	11.92 V
1774136585	0 Pkt	-71 dBm	11.92 V
1774134763	0 Pkt	-72 dBm	11.92 V
1774132941	0 Pkt	-71 dBm	11.81 V
1774131119	0 Pkt	-74 dBm	11.92 V
1774129297	0 Pkt	-75 dBm	11.92 V
1774127475	0 Pkt	-73 dBm	11.92 V
1774125653	0 Pkt	-72 dBm	11.92 V
1774123832	2 Pkt	-68 dBm	11.92 V
1774122009	1 Pkt	-70 dBm	11.81 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)