APRS Track Direct

My position About ☰

reset

DG0OPK-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0OPK-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp.in*	Hum*	Temp.out*
1786735832	35.9 C deg	28.5 %	22 C deg
1786735360	35.9 C deg	28.5 %	22 C deg
1786733397	36 C deg	28.5 %	24 C deg
1786731469	36 C deg	28.2 %	25.9 C deg
1786729455	36.2 C deg	28.1 %	34.8 C deg
1786728422	36 C deg	29 %	37.3 C deg
1786727661	36 C deg	29 %	37.3 C deg
1786725843	35.8 C deg	28.1 %	34.6 C deg
1786724105	35.8 C deg	28.2 %	36.9 C deg
1786722610	35.5 C deg	28.6 %	35.8 C deg
1786720535	35.5 C deg	28.2 %	36.2 C deg
1786718587	35 C deg	29.7 %	33.2 C deg
1786716864	34.7 C deg	29.3 %	32.8 C deg
1786714981	34.4 C deg	29.1 %	31.3 C deg
1786713568	34.5 C deg	27.3 %	31.4 C deg
1786711549	34.4 C deg	27.7 %	29.9 C deg
1786709576	34.1 C deg	27.9 %	30 C deg
1786708343	33.7 C deg	27.4 %	30.4 C deg
1786707682	33.7 C deg	27.4 %	30.4 C deg
1786706405	33.3 C deg	27.9 %	29.9 C deg
1786705924	33.3 C deg	27.9 %	29.9 C deg
1786704203	32.8 C deg	28.2 %	29.3 C deg
1786703083	32.6 C deg	28.6 %	28 C deg
1786702368	32.6 C deg	28.6 %	28 C deg
1786700613	32 C deg	28.8 %	27.2 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)