APRS Track Direct

My position About ☰

reset

YE1BPQ-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YE1BPQ-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274546	0 Pkt	-65 dBm	12.06 V
1762360848	0 Pkt	-70 dBm	12.06 V
1762359026	0 Pkt	-69 dBm	12.06 V
1762357204	0 Pkt	-70 dBm	12.06 V
1762355382	0 Pkt	-69 dBm	12.06 V
1762353560	0 Pkt	-69 dBm	12.06 V
1762351738	1 Pkt	-70 dBm	12.06 V
1762349915	1 Pkt	-70 dBm	12.06 V
1762348093	0 Pkt	-70 dBm	12.02 V
1762346271	0 Pkt	-71 dBm	12.02 V
1762344449	0 Pkt	-71 dBm	12.06 V
1762342628	0 Pkt	-70 dBm	12.06 V
1762340805	0 Pkt	-70 dBm	12.06 V
1762338991	0 Pkt	-70 dBm	12.06 V
1762337161	1 Pkt	-70 dBm	12.02 V
1762335340	0 Pkt	-70 dBm	12.06 V
1762333518	1 Pkt	-70 dBm	12.06 V
1762331695	1 Pkt	-70 dBm	12.06 V
1762329873	0 Pkt	-71 dBm	12.06 V
1762328051	0 Pkt	-71 dBm	12.02 V
1762326229	0 Pkt	-70 dBm	12.06 V
1762324407	0 Pkt	-70 dBm	12.06 V
1762322585	0 Pkt	-70 dBm	12.06 V
1762320765	2 Pkt	-70 dBm	12.06 V
1762318941	0 Pkt	-71 dBm	12.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)