APRS Track Direct

My position About ☰

reset

LD4AI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LD4AI. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1732286509	12.6 Volt	600 Pkt	71 Pcnt	4 C
1732286209	12.6 Volt	610 Pkt	71 Pcnt	4 C
1732285908	12.6 Volt	610 Pkt	72 Pcnt	4 C
1732285608	12.6 Volt	600 Pkt	71 Pcnt	4 C
1732285308	12.6 Volt	580 Pkt	70 Pcnt	4.5 C
1732285007	12.6 Volt	570 Pkt	71 Pcnt	4.5 C
1732284707	12.6 Volt	570 Pkt	70 Pcnt	4.5 C
1732284407	12.6 Volt	560 Pkt	70 Pcnt	4.5 C
1732284107	12.6 Volt	530 Pkt	70 Pcnt	4.5 C
1732283806	12.6 Volt	530 Pkt	70 Pcnt	4.5 C
1732283506	12.6 Volt	520 Pkt	69 Pcnt	4.5 C
1732283206	12.6 Volt	490 Pkt	70 Pcnt	4.5 C
1732282905	12.6 Volt	480 Pkt	69 Pcnt	4.5 C
1732282605	12.6 Volt	490 Pkt	69 Pcnt	4.5 C
1732282305	12.6 Volt	470 Pkt	69 Pcnt	4.5 C
1732282005	12.6 Volt	490 Pkt	69 Pcnt	4.5 C
1732281704	12.6 Volt	510 Pkt	70 Pcnt	4.5 C
1732281404	12.6 Volt	530 Pkt	70 Pcnt	4.5 C
1732281104	12.6 Volt	540 Pkt	71 Pcnt	4.5 C
1732280803	12.6 Volt	550 Pkt	71 Pcnt	4.5 C
1732280503	12.6 Volt	570 Pkt	71 Pcnt	4.5 C
1732280203	12.6 Volt	580 Pkt	70 Pcnt	4.5 C
1732279902	12.6 Volt	600 Pkt	71 Pcnt	4.5 C
1732279602	12.6 Volt	600 Pkt	71 Pcnt	4.5 C
1732279302	12.6 Volt	620 Pkt	71 Pcnt	4.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)