APRS Track Direct

My position About ☰

reset

SR8WXO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1782477596	90 Pkt	10 Pkt	8 Pkt
1782476994	82 Pkt	11 Pkt	9 Pkt
1782476391	85 Pkt	21 Pkt	15 Pkt
1782475781	83 Pkt	14 Pkt	12 Pkt
1782475178	72 Pkt	9 Pkt	7 Pkt
1782474575	86 Pkt	12 Pkt	10 Pkt
1782473972	102 Pkt	20 Pkt	14 Pkt
1782473363	72 Pkt	14 Pkt	12 Pkt
1782472760	79 Pkt	14 Pkt	12 Pkt
1782472157	91 Pkt	14 Pkt	12 Pkt
1782471554	89 Pkt	17 Pkt	11 Pkt
1782470944	91 Pkt	11 Pkt	9 Pkt
1782470342	101 Pkt	11 Pkt	9 Pkt
1782469739	93 Pkt	8 Pkt	6 Pkt
1782469136	82 Pkt	15 Pkt	9 Pkt
1782468526	100 Pkt	11 Pkt	9 Pkt
1782467923	79 Pkt	10 Pkt	8 Pkt
1782467321	89 Pkt	8 Pkt	6 Pkt
1782466718	91 Pkt	15 Pkt	9 Pkt
1782466108	84 Pkt	12 Pkt	10 Pkt
1782465505	80 Pkt	12 Pkt	10 Pkt
1782464902	76 Pkt	11 Pkt	9 Pkt
1782464299	68 Pkt	15 Pkt	9 Pkt
1782463690	97 Pkt	13 Pkt	11 Pkt
1782463087	84 Pkt	13 Pkt	11 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)