APRS Track Direct

My position About ☰

reset

WR7DW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WR7DW-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*	Temp*
1758182202	13.28 Volt	440 Pkt	130 Pkt	79 Pcnt	15.5 C
1758178603	13.28 Volt	450 Pkt	130 Pkt	80 Pcnt	16 C
1758175002	13.28 Volt	460 Pkt	140 Pkt	75 Pcnt	16 C
1758171404	13.28 Volt	460 Pkt	130 Pkt	78 Pcnt	16.5 C
1758167802	13.35 Volt	490 Pkt	130 Pkt	81 Pcnt	16.5 C
1758164207	13.35 Volt	470 Pkt	130 Pkt	77 Pcnt	17 C
1758160603	13.35 Volt	500 Pkt	140 Pkt	82 Pcnt	16.5 C
1758157007	13.58 Volt	560 Pkt	180 Pkt	82 Pcnt	16 C
1758153406	14.1 Volt	550 Pkt	190 Pkt	84 Pcnt	15.5 C
1758149801	14.48 Volt	520 Pkt	170 Pkt	84 Pcnt	15 C
1758146199	14.48 Volt	470 Pkt	180 Pkt	78 Pcnt	15 C
1758142605	14.4 Volt	510 Pkt	220 Pkt	78 Pcnt	14.5 C
1758139008	14.4 Volt	440 Pkt	150 Pkt	75 Pcnt	14.5 C
1758135401	14.4 Volt	350 Pkt	110 Pkt	75 Pcnt	14 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)