APRS Track Direct

My position About ☰

reset

W9IPA-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W9IPA-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732524568	12.9 Volt	190 Pkt	50 Pkt	86 Pcnt
1732523368	12.9 Volt	210 Pkt	50 Pkt	89 Pcnt
1732522168	12.9 Volt	210 Pkt	50 Pkt	93 Pcnt
1732520968	12.9 Volt	220 Pkt	50 Pkt	91 Pcnt
1732519768	12.83 Volt	220 Pkt	50 Pkt	90 Pcnt
1732518568	12.83 Volt	230 Pkt	50 Pkt	90 Pcnt
1732517368	12.9 Volt	230 Pkt	50 Pkt	90 Pcnt
1732516168	12.83 Volt	220 Pkt	50 Pkt	89 Pcnt
1732514968	12.83 Volt	200 Pkt	40 Pkt	87 Pcnt
1732513768	12.9 Volt	190 Pkt	50 Pkt	89 Pcnt
1732512568	12.83 Volt	180 Pkt	50 Pkt	86 Pcnt
1732511368	12.9 Volt	190 Pkt	50 Pkt	87 Pcnt
1732510168	12.9 Volt	180 Pkt	50 Pkt	86 Pcnt
1732508968	12.83 Volt	200 Pkt	60 Pkt	88 Pcnt
1732507769	12.83 Volt	240 Pkt	70 Pkt	90 Pcnt
1732506569	12.9 Volt	270 Pkt	80 Pkt	90 Pcnt
1732505369	12.9 Volt	280 Pkt	80 Pkt	89 Pcnt
1732504169	12.9 Volt	300 Pkt	80 Pkt	82 Pcnt
1732502969	12.9 Volt	300 Pkt	80 Pkt	76 Pcnt
1732501769	12.9 Volt	310 Pkt	80 Pkt	72 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)