APRS Track Direct

My position About ☰

reset

W8MAI-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W8MAI-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U1*	Temp*	Rx1h*	Dg1h*
1732571527	13.4 Volt	13.5 C	30 Pkt	10 Pkt
1732571527	13.4 Volt	13.5 C	30 Pkt	10 Pkt
1732569728	13.4 Volt	13.5 C	20 Pkt	10 Pkt
1732569727	13.4 Volt	13.5 C	20 Pkt	10 Pkt
1732567928	13.4 Volt	13 C	20 Pkt	10 Pkt
1732567927	13.4 Volt	13 C	20 Pkt	10 Pkt
1732566128	13.4 Volt	13 C	30 Pkt	10 Pkt
1732566127	13.4 Volt	13 C	30 Pkt	10 Pkt
1732564328	13.4 Volt	13 C	30 Pkt	20 Pkt
1732564327	13.4 Volt	13 C	30 Pkt	20 Pkt
1732562528	13.4 Volt	13 C	40 Pkt	20 Pkt
1732562527	13.4 Volt	13 C	40 Pkt	20 Pkt
1732560728	13.4 Volt	13 C	50 Pkt	30 Pkt
1732560727	13.4 Volt	13 C	50 Pkt	30 Pkt
1732558928	13.4 Volt	12.5 C	50 Pkt	30 Pkt
1732558927	13.4 Volt	12.5 C	50 Pkt	30 Pkt
1732557128	13.4 Volt	12 C	40 Pkt	20 Pkt
1732557127	13.4 Volt	12 C	40 Pkt	20 Pkt
1732555328	13.4 Volt	11.5 C	40 Pkt	20 Pkt
1732555327	13.4 Volt	11.5 C	40 Pkt	20 Pkt
1732553528	13.4 Volt	11.5 C	40 Pkt	20 Pkt
1732553528	13.4 Volt	11.5 C	40 Pkt	20 Pkt
1732551728	13.4 Volt	11 C	40 Pkt	20 Pkt
1732551727	13.4 Volt	11 C	40 Pkt	20 Pkt
1732549929	13.4 Volt	11 C	50 Pkt	30 Pkt

*Used Equation Coefficients:

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)