APRS Track Direct

My position About ☰

reset

E24TVS-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24TVS-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274638	0 Pkt	-70 dBm	13.08 V
1762269897	0 Pkt	-60 dBm	12.98 V
1762268675	0 Pkt	-59 dBm	13.13 V
1762267453	0 Pkt	-60 dBm	12.98 V
1762266231	1 Pkt	-60 dBm	13.13 V
1762264993	0 Pkt	-59 dBm	13.13 V
1762263771	0 Pkt	-59 dBm	12.98 V
1762262550	0 Pkt	-59 dBm	13.1 V
1762261328	0 Pkt	-59 dBm	12.98 V
1762260106	0 Pkt	-60 dBm	12.98 V
1762258884	0 Pkt	-60 dBm	12.96 V
1762257662	0 Pkt	-59 dBm	13.13 V
1762256440	0 Pkt	-60 dBm	13.13 V
1762255218	0 Pkt	-58 dBm	13.1 V
1762253996	0 Pkt	-59 dBm	12.96 V
1762252774	0 Pkt	-59 dBm	13.13 V
1762251552	0 Pkt	-59 dBm	13.1 V
1762250332	0 Pkt	-59 dBm	13.1 V
1762249108	0 Pkt	-59 dBm	13.1 V
1762247886	0 Pkt	-59 dBm	12.94 V
1762246637	0 Pkt	-58 dBm	13.1 V
1762245415	0 Pkt	-59 dBm	12.96 V
1762244193	0 Pkt	-59 dBm	12.98 V
1762242971	0 Pkt	-59 dBm	13.13 V
1762241749	0 Pkt	-60 dBm	13.1 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)