APRS Track Direct

My position About ☰

reset

OE6VAG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE6VAG. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Eff1h*	Temp*
1778027158	12.53 Volt	100 Pcnt	18 C
1778025359	12.53 Volt	100 Pcnt	18 C
1778023559	12.53 Volt	100 Pcnt	18 C
1778021759	12.53 Volt	100 Pcnt	18 C
1778019959	12.53 Volt	100 Pcnt	18.5 C
1778018159	12.53 Volt	100 Pcnt	18.5 C
1778016359	12.53 Volt	100 Pcnt	18.5 C
1778014559	12.53 Volt	100 Pcnt	18.5 C
1778012759	12.53 Volt	100 Pcnt	19 C
1778010959	12.53 Volt	100 Pcnt	18.5 C
1778009159	12.53 Volt	100 Pcnt	18.5 C
1778007359	12.53 Volt	100 Pcnt	18.5 C
1778005559	12.53 Volt	100 Pcnt	18.5 C
1778003759	12.53 Volt	100 Pcnt	18 C
1778001959	12.53 Volt	100 Pcnt	18 C
1778000159	12.53 Volt	100 Pcnt	18 C
1777998359	12.53 Volt	100 Pcnt	18 C
1777996559	12.53 Volt	100 Pcnt	18 C
1777994760	12.53 Volt	100 Pcnt	18 C
1777992960	12.53 Volt	100 Pcnt	18 C
1777991160	12.53 Volt	100 Pcnt	18 C
1777989360	12.53 Volt	100 Pcnt	18 C
1777987560	12.53 Volt	100 Pcnt	18 C
1777985760	12.53 Volt	100 Pcnt	18 C
1777983960	12.53 Volt	100 Pcnt	18 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)