APRS Track Direct

My position About ☰

reset

9W2LOV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9W2LOV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1782503514	0 Pkt	-54 dBm	0.1 V
1782503191	0 Pkt	-54 dBm	0.1 V
1782502867	0 Pkt	-52 dBm	0.1 V
1782502544	0 Pkt	-53 dBm	0.08 V
1782502220	0 Pkt	-53 dBm	0.1 V
1782501897	0 Pkt	-53 dBm	0.1 V
1782501573	1 Pkt	-52 dBm	0.1 V
1782501250	0 Pkt	-53 dBm	0.1 V
1782500927	1 Pkt	-56 dBm	0.1 V
1782500603	1 Pkt	-53 dBm	0.1 V
1782500327	0 Pkt	-51 dBm	0.1 V
1782500003	0 Pkt	-50 dBm	0.1 V
1782499680	0 Pkt	-53 dBm	0.1 V
1782499356	0 Pkt	-54 dBm	0.1 V
1782499032	0 Pkt	-53 dBm	0.1 V
1782498709	0 Pkt	-54 dBm	0.1 V
1782498385	0 Pkt	-53 dBm	0.08 V
1782498062	0 Pkt	-53 dBm	0.1 V
1782497738	0 Pkt	-53 dBm	0.1 V
1782497415	0 Pkt	-53 dBm	0.1 V
1782497092	0 Pkt	-53 dBm	0.1 V
1782496768	0 Pkt	-51 dBm	0.1 V
1782496444	0 Pkt	-51 dBm	0.1 V
1782496121	1 Pkt	-51 dBm	0.1 V
1782495797	0 Pkt	-51 dBm	0.1 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)