APRS Track Direct

My position About ☰

reset

TB8ATA-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TB8ATA-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1754148004	1 Pkt	-59 dBm	12.3 V
1754147645	6 Pkt	-59 dBm	12.43 V
1754147022	0 Pkt	-60 dBm	12.3 V
1754146896	3 Pkt	-60 dBm	12.43 V
1754146274	0 Pkt	-58 dBm	12.43 V
1754145912	9 Pkt	-60 dBm	12.45 V
1754145289	3 Pkt	-62 dBm	12.43 V
1754144924	19 Pkt	-59 dBm	12.43 V
1754144300	0 Pkt	-62 dBm	12.43 V
1754143936	13 Pkt	-60 dBm	12.43 V
1754143312	1 Pkt	-62 dBm	12.43 V
1754143189	10 Pkt	-60 dBm	12.43 V
1754142565	1 Pkt	-60 dBm	12.43 V
1754142202	9 Pkt	-60 dBm	12.3 V
1754141578	0 Pkt	-60 dBm	12.43 V
1754141339	7 Pkt	-62 dBm	12.43 V
1754140716	0 Pkt	-60 dBm	12.43 V
1754140355	10 Pkt	-60 dBm	12.43 V
1754139732	1 Pkt	-62 dBm	12.43 V
1754139608	6 Pkt	-61 dBm	12.3 V
1754138984	2 Pkt	-61 dBm	12.3 V
1754138505	10 Pkt	-60 dBm	12.33 V
1754137923	9 Pkt	-61 dBm	12.43 V
1754137258	0 Pkt	-60 dBm	12.43 V
1754136899	17 Pkt	-60 dBm	12.43 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)