APRS Track Direct

My position About ☰

reset

TA3LG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA3LG. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1758202872	3 Pkt	-33 dBm	4.63 V
1758201941	0 Pkt	-33 dBm	4.63 V
1758201016	0 Pkt	-33 dBm	4.63 V
1758200091	0 Pkt	-38 dBm	4.61 V
1758199167	0 Pkt	-34 dBm	4.63 V
1758198242	0 Pkt	-40 dBm	4.68 V
1758197317	0 Pkt	-37 dBm	4.68 V
1758196391	2 Pkt	-40 dBm	4.68 V
1758195464	0 Pkt	-40 dBm	4.68 V
1758194539	0 Pkt	-35 dBm	4.7 V
1758193614	0 Pkt	-32 dBm	4.68 V
1758192689	2 Pkt	-32 dBm	4.7 V
1758191761	1 Pkt	-32 dBm	4.7 V
1758190836	2 Pkt	-32 dBm	4.7 V
1758189907	0 Pkt	-33 dBm	4.68 V
1758188983	0 Pkt	-33 dBm	4.7 V
1758188058	0 Pkt	-33 dBm	4.7 V
1758187133	0 Pkt	-36 dBm	4.68 V
1758186208	0 Pkt	-39 dBm	4.7 V
1758185283	2 Pkt	-37 dBm	4.68 V
1758184356	0 Pkt	-40 dBm	4.68 V
1758183431	4 Pkt	-34 dBm	4.63 V
1758182499	0 Pkt	-37 dBm	4.68 V
1758181574	2 Pkt	-39 dBm	4.68 V
1758180648	0 Pkt	-38 dBm	4.68 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)