APRS Track Direct

My position About ☰

reset

BX4AEF-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX4AEF-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1774114801	32.1 C	13 p	30 p	2564 p
1774113601	33.2 C	8 p	27 p	2551 p
1774112400	32.6 C	9 p	32 p	2543 p
1774111200	33.8 C	10 p	32 p	2534 p
1774110001	33.8 C	13 p	40 p	2524 p
1774108801	33.9 C	9 p	48 p	2511 p
1774107601	34.9 C	18 p	53 p	2502 p
1774106401	34.3 C	21 p	64 p	2484 p
1774105201	33.1 C	14 p	64 p	2463 p
1774104001	31.2 C	29 p	63 p	2458 p
1774102801	31.7 C	21 p	59 p	2446 p
1774101601	31.4 C	13 p	67 p	2446 p
1774100401	31.9 C	25 p	70 p	2447 p
1774099201	31.2 C	29 p	67 p	2438 p
1774098001	30 C	16 p	77 p	2418 p
1774096801	31 C	22 p	77 p	2402 p
1774095601	30 C	39 p	74 p	2380 p
1774094401	30.5 C	16 p	46 p	2341 p
1774093201	31 C	19 p	63 p	2325 p
1774092001	32 C	11 p	82 p	2306 p
1774090801	30.8 C	33 p	97 p	2295 p
1774089601	32.1 C	38 p	99 p	2262 p
1774088401	31.1 C	26 p	253 p	2224 p
1774087201	32.5 C	35 p	366 p	2198 p
1774086001	31.5 C	192 p	381 p	2163 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)