APRS Track Direct

My position About ☰

reset

OK1TOR-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1TOR-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPU_temp*	Load*	Fmem*	Nodes[I]*	Dests[F]*
1774104484	55.8 °C	0.69	48 MB	305	49
1774103764	55.8 °C	0.76	46 MB	305	49
1774102322	55.3 °C	0.74	47 MB	305	49
1774100170	55.8 °C	0.73	45 MB	320	49
1774099450	61.2 °C	1.03	46 MB	320	49
1774097289	55.3 °C	0.48	48 MB	316	49
1774095848	62.3 °C	1.4	47 MB	316	49
1774095127	54.7 °C	0.67	45 MB	307	49
1774094407	55.3 °C	0.31	43 MB	307	49
1774092245	62.3 °C	1.31	45 MB	307	49
1774091525	54.7 °C	0.64	45 MB	306	49
1774089363	55.8 °C	0.69	41 MB	307	49
1774087202	54.2 °C	0.93	41 MB	303	47
1774083610	54.2 °C	0.54	42 MB	303	47
1774082890	53.6 °C	0.5	45 MB	315	47
1774079287	54.2 °C	0.65	42 MB	321	47
1774077846	61.7 °C	1.28	44 MB	320	47
1774077126	53.6 °C	0.61	44 MB	307	47
1774075685	53.6 °C	0.66	43 MB	307	47
1774074964	53.6 °C	0.85	46 MB	307	47
1774070641	61.2 °C	1.59	46 MB	313	47
1774069210	53.6 °C	1.16	43 MB	308	47
1774067769	54.7 °C	0.61	42 MB	310	47
1774067048	60.1 °C	1.64	43 MB	310	47
1774065607	53.6 °C	0.76	40 MB	310	47

*Used Equation Coefficients:

CPU_temp: 0, 0.1, 0

Load: 0, 0.01, 0

Fmem: 0, 1, 0

Nodes[I]: 0, 1, 0

Dests[F]: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)