APRS Track Direct

My position About ☰

reset

SR9SMR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9SMR. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Rx10min*	Tx10min*	Vbatt*
1790640257	36 Pkt	2 Pkt	11.86 V
1790637849	42 Pkt	2 Pkt	11.88 V
1790635498	43 Pkt	2 Pkt	11.9 V
1790634765	35 Pkt	2 Pkt	11.86 V
1790633664	34 Pkt	2 Pkt	11.86 V
1790632393	34 Pkt	2 Pkt	11.86 V
1790630924	38 Pkt	3 Pkt	11.82 V
1790628529	32 Pkt	2 Pkt	11.86 V
1790627773	34 Pkt	2 Pkt	11.88 V
1790623846	44 Pkt	1 Pkt	11.88 V
1790623102	32 Pkt	3 Pkt	11.84 V
1790621627	38 Pkt	2 Pkt	11.88 V
1790620334	35 Pkt	2 Pkt	11.88 V
1790619589	31 Pkt	2 Pkt	11.88 V
1790617680	33 Pkt	1 Pkt	11.9 V
1790616021	33 Pkt	2 Pkt	11.88 V
1790614545	37 Pkt	2 Pkt	11.9 V
1790613071	37 Pkt	2 Pkt	11.82 V
1790611561	34 Pkt	3 Pkt	11.9 V
1790610082	43 Pkt	2 Pkt	11.92 V
1790607839	36 Pkt	2 Pkt	11.9 V
1790606599	41 Pkt	2 Pkt	11.9 V
1790605855	39 Pkt	2 Pkt	11.92 V
1790602851	36 Pkt	3 Pkt	11.9 V
1790601678	33 Pkt	2 Pkt	11.92 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)