APRS Track Direct

My position About ☰

reset

AI5TX-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI5TX-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1764268283	12.68 Volt	110 Pkt	50 Pkt	44 Pcnt
1764264683	12.68 Volt	100 Pkt	40 Pkt	36 Pcnt
1764261083	12.68 Volt	150 Pkt	50 Pkt	50 Pcnt
1764257483	12.68 Volt	180 Pkt	60 Pkt	54 Pcnt
1764253883	12.68 Volt	120 Pkt	50 Pkt	39 Pcnt
1764250283	12.68 Volt	140 Pkt	60 Pkt	45 Pcnt
1764246683	12.68 Volt	140 Pkt	50 Pkt	45 Pcnt
1764243083	12.68 Volt	150 Pkt	60 Pkt	47 Pcnt
1764239484	12.68 Volt	140 Pkt	50 Pkt	42 Pcnt
1764235884	12.68 Volt	110 Pkt	40 Pkt	41 Pcnt
1764232301	12.68 Volt	130 Pkt	50 Pkt	43 Pcnt
1764228684	12.68 Volt	180 Pkt	60 Pkt	52 Pcnt
1764225084	12.68 Volt	160 Pkt	60 Pkt	51 Pcnt
1764221484	12.68 Volt	150 Pkt	50 Pkt	55 Pcnt
1764217884	12.68 Volt	140 Pkt	50 Pkt	50 Pcnt
1764214284	12.68 Volt	130 Pkt	50 Pkt	49 Pcnt
1764210684	12.68 Volt	130 Pkt	50 Pkt	50 Pcnt
1764207084	12.68 Volt	120 Pkt	60 Pkt	49 Pcnt
1764203484	12.68 Volt	120 Pkt	40 Pkt	47 Pcnt
1764199884	12.68 Volt	120 Pkt	40 Pkt	49 Pcnt
1764196284	12.68 Volt	120 Pkt	50 Pkt	49 Pcnt
1764192685	12.68 Volt	110 Pkt	50 Pkt	44 Pcnt
1764189085	12.68 Volt	110 Pkt	40 Pkt	49 Pcnt
1764185485	12.68 Volt	100 Pkt	40 Pkt	42 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)