APRS Track Direct

My position About ☰

reset

VK2JUZ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2JUZ-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1754131892	12.83 Volt	160 Pkt	98 Pcnt
1754131592	12.83 Volt	160 Pkt	98 Pcnt
1754131292	12.83 Volt	160 Pkt	98 Pcnt
1754130992	12.9 Volt	160 Pkt	98 Pcnt
1754130692	12.9 Volt	150 Pkt	97 Pcnt
1754130392	13.05 Volt	160 Pkt	97 Pcnt
1754130092	12.83 Volt	150 Pkt	95 Pcnt
1754129792	13.2 Volt	160 Pkt	95 Pcnt
1754129492	13.13 Volt	150 Pkt	96 Pcnt
1754129192	13.2 Volt	150 Pkt	96 Pcnt
1754128892	13.05 Volt	160 Pkt	95 Pcnt
1754128592	12.98 Volt	150 Pkt	95 Pcnt
1754128292	13.13 Volt	150 Pkt	95 Pcnt
1754127992	13.2 Volt	150 Pkt	95 Pcnt
1754127692	13.2 Volt	150 Pkt	95 Pcnt
1754127392	12.98 Volt	150 Pkt	95 Pcnt
1754127092	12.9 Volt	160 Pkt	96 Pcnt
1754126792	12.98 Volt	160 Pkt	96 Pcnt
1754126492	12.75 Volt	160 Pkt	97 Pcnt
1754126192	12.9 Volt	160 Pkt	97 Pcnt
1754125892	12.9 Volt	160 Pkt	97 Pcnt
1754125592	13.13 Volt	150 Pkt	96 Pcnt
1754125292	12.83 Volt	150 Pkt	96 Pcnt
1754124992	12.98 Volt	150 Pkt	96 Pcnt
1754124692	13.2 Volt	160 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)