APRS Track Direct

My position About ☰

reset

TB2HSI-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TB2HSI-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1779841888	0 Pkt	-47 dBm	12.43 V
1779841566	0 Pkt	-46 dBm	12.43 V
1779841243	1 Pkt	-47 dBm	12.43 V
1779840922	0 Pkt	-47 dBm	12.43 V
1779840600	1 Pkt	-45 dBm	12.43 V
1779840277	0 Pkt	-44 dBm	12.43 V
1779839955	0 Pkt	-45 dBm	12.43 V
1779839633	1 Pkt	-47 dBm	12.43 V
1779839311	0 Pkt	-49 dBm	12.43 V
1779838989	0 Pkt	-46 dBm	12.43 V
1779838667	1 Pkt	-45 dBm	12.43 V
1779838345	0 Pkt	-46 dBm	12.43 V
1779838023	0 Pkt	-47 dBm	12.43 V
1779837701	0 Pkt	-45 dBm	12.43 V
1779837379	0 Pkt	-51 dBm	12.43 V
1779837057	0 Pkt	-49 dBm	12.43 V
1779836735	0 Pkt	-49 dBm	12.43 V
1779836413	0 Pkt	-52 dBm	12.43 V
1779836091	1 Pkt	-52 dBm	12.43 V
1779835769	0 Pkt	-50 dBm	12.43 V
1779835447	0 Pkt	-50 dBm	12.43 V
1779835125	0 Pkt	-52 dBm	12.43 V
1779834803	0 Pkt	-53 dBm	12.43 V
1779834481	1 Pkt	-52 dBm	12.43 V
1779834159	0 Pkt	-53 dBm	12.43 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)