APRS Track Direct

My position About ☰

reset

YD0RDD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD0RDD-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1751273432	0 Pkt	-26 dBm	0.14 V
1751271610	0 Pkt	-38 dBm	0.14 V
1751269788	0 Pkt	-34 dBm	0.14 V
1751267966	0 Pkt	-34 dBm	0.14 V
1751266144	0 Pkt	-37 dBm	0.14 V
1751264322	0 Pkt	-24 dBm	0.14 V
1751262500	0 Pkt	-22 dBm	0.14 V
1751260680	0 Pkt	-22 dBm	0.14 V
1751258856	0 Pkt	-27 dBm	0.14 V
1751257034	0 Pkt	-21 dBm	0.14 V
1751255212	0 Pkt	-23 dBm	0.14 V
1751253390	0 Pkt	-24 dBm	0.14 V
1751251568	0 Pkt	-24 dBm	0.14 V
1751249746	0 Pkt	-27 dBm	0.14 V
1751247941	2 Pkt	-28 dBm	0.14 V
1751246102	0 Pkt	-21 dBm	0.14 V
1751244280	1 Pkt	-24 dBm	0.14 V
1751242457	0 Pkt	-21 dBm	0.14 V
1751240635	0 Pkt	-27 dBm	0.14 V
1751238813	0 Pkt	-19 dBm	0.14 V
1751236991	0 Pkt	-28 dBm	0.14 V
1751235169	0 Pkt	-28 dBm	0.14 V
1751233347	0 Pkt	-26 dBm	0.14 V
1751231525	0 Pkt	-18 dBm	0.14 V
1751229703	0 Pkt	-23 dBm	0.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)