APRS Track Direct

My position About ☰

reset

KC9NPJ-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC9NPJ-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vlt*	Rx1h*	Eff1h*
1774123135	13.65 Volt	20 Pkt	26 Pcnt
1774121335	13.65 Volt	30 Pkt	30 Pcnt
1774119535	13.58 Volt	30 Pkt	19 Pcnt
1774117735	13.65 Volt	50 Pkt	15 Pcnt
1774115935	13.65 Volt	80 Pkt	17 Pcnt
1774114135	13.65 Volt	120 Pkt	17 Pcnt
1774112335	13.65 Volt	360 Pkt	32 Pcnt
1774110535	13.65 Volt	540 Pkt	39 Pcnt
1774108735	13.65 Volt	510 Pkt	36 Pcnt
1774106936	12.53 Volt	520 Pkt	36 Pcnt
1774105136	13.58 Volt	430 Pkt	29 Pcnt
1774103336	13.58 Volt	510 Pkt	34 Pcnt
1774101536	13.65 Volt	830 Pkt	49 Pcnt
1774099736	13.58 Volt	980 Pkt	53 Pcnt
1774097936	13.58 Volt	960 Pkt	55 Pcnt
1774096136	13.58 Volt	790 Pkt	49 Pcnt
1774094336	13.58 Volt	690 Pkt	44 Pcnt
1774092536	13.58 Volt	600 Pkt	40 Pcnt
1774090736	13.58 Volt	360 Pkt	29 Pcnt
1774088936	13.58 Volt	340 Pkt	27 Pcnt
1774087136	13.58 Volt	450 Pkt	35 Pcnt
1774085337	13.58 Volt	340 Pkt	31 Pcnt
1774083537	13.58 Volt	230 Pkt	25 Pcnt
1774081737	13.58 Volt	250 Pkt	30 Pcnt
1774079937	13.58 Volt	230 Pkt	28 Pcnt

*Used Equation Coefficients:

Vlt: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)