APRS Track Direct

My position About ☰

reset

YG2BMZ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YG2BMZ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1763304214	0 Pkt	-28 dBm	0.1 V
1763303893	0 Pkt	-26 dBm	0.14 V
1763303570	0 Pkt	-27 dBm	0.43 V
1763303248	1 Pkt	-27 dBm	0 V
1763302926	0 Pkt	-27 dBm	0.14 V
1763302603	0 Pkt	-25 dBm	0.12 V
1763302283	0 Pkt	-28 dBm	0.12 V
1763301959	0 Pkt	-26 dBm	0.16 V
1763301637	0 Pkt	-28 dBm	0.43 V
1763301315	0 Pkt	-29 dBm	0.18 V
1763300995	2 Pkt	-29 dBm	0.16 V
1763300672	1 Pkt	-30 dBm	0.06 V
1763300352	0 Pkt	-28 dBm	0.06 V
1763300027	0 Pkt	-28 dBm	0.16 V
1763299705	0 Pkt	-28 dBm	0 V
1763299384	0 Pkt	-29 dBm	0.02 V
1763299061	0 Pkt	-28 dBm	0 V
1763298739	1 Pkt	-29 dBm	0.39 V
1763298417	0 Pkt	-29 dBm	0.18 V
1763298096	0 Pkt	-27 dBm	0.27 V
1763297776	0 Pkt	-35 dBm	0.02 V
1763297453	0 Pkt	-29 dBm	0.29 V
1763297135	0 Pkt	-28 dBm	0.02 V
1763296807	0 Pkt	-31 dBm	0 V
1763296488	0 Pkt	-29 dBm	0 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)