APRS Track Direct

My position About ☰

reset

HS7BHK-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS7BHK-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1753647475	0 Pkt	-64 dBm	0.55 V
1753643780	0 Pkt	-65 dBm	0.55 V
1753640156	0 Pkt	-65 dBm	0.55 V
1753636533	0 Pkt	-65 dBm	0.55 V
1753632910	0 Pkt	-66 dBm	0.55 V
1753629286	1 Pkt	-66 dBm	0.53 V
1753625662	0 Pkt	-65 dBm	0.53 V
1753622039	0 Pkt	-66 dBm	0.53 V
1753618416	1 Pkt	-66 dBm	0.53 V
1753614791	0 Pkt	-66 dBm	0.51 V
1753611168	0 Pkt	-66 dBm	0.49 V
1753607545	0 Pkt	-63 dBm	0.49 V
1753603922	0 Pkt	-64 dBm	0.49 V
1753600299	0 Pkt	-65 dBm	0.49 V
1753596675	0 Pkt	-63 dBm	0.49 V
1753593052	1 Pkt	-64 dBm	0.51 V
1753589427	0 Pkt	-63 dBm	0.53 V
1753585803	0 Pkt	-63 dBm	0.55 V
1753582180	0 Pkt	-63 dBm	0.57 V
1753578556	0 Pkt	-63 dBm	0.57 V
1753574933	0 Pkt	-63 dBm	0.57 V
1753571309	0 Pkt	-63 dBm	0.57 V
1753567686	0 Pkt	-63 dBm	0.57 V
1753564063	11 Pkt	-64 dBm	0.57 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)