APRS Track Direct

My position About ☰

reset

HS5UKT-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5UKT-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1762299927	0 Pkt	-68 dBm	11.65 V
1762299303	0 Pkt	-67 dBm	11.65 V
1762298679	1 Pkt	-66 dBm	11.65 V
1762298055	1 Pkt	-68 dBm	11.65 V
1762297431	0 Pkt	-66 dBm	11.65 V
1762296807	0 Pkt	-66 dBm	11.65 V
1762296183	0 Pkt	-66 dBm	11.63 V
1762295559	0 Pkt	-65 dBm	11.65 V
1762294935	0 Pkt	-66 dBm	11.65 V
1762294311	0 Pkt	-66 dBm	11.63 V
1762293687	0 Pkt	-65 dBm	11.63 V
1762275271	0 Pkt	-64 dBm	11.65 V
1762274647	0 Pkt	-63 dBm	11.65 V
1762274023	0 Pkt	-65 dBm	11.65 V
1762273399	2 Pkt	-67 dBm	11.65 V
1762272775	0 Pkt	-67 dBm	11.65 V
1762272151	1 Pkt	-65 dBm	11.65 V
1762271527	0 Pkt	-65 dBm	11.65 V
1762270902	0 Pkt	-66 dBm	11.65 V
1762270279	0 Pkt	-66 dBm	11.65 V
1762269655	0 Pkt	-65 dBm	11.63 V
1762269031	0 Pkt	-67 dBm	11.65 V
1762268407	0 Pkt	-66 dBm	11.65 V
1762267783	0 Pkt	-67 dBm	11.65 V
1762267159	0 Pkt	-68 dBm	11.63 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)