APRS Track Direct

My position About ☰

reset

TA4UZE-D Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA4UZE-D. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1786739466	5 Pkt	-75 dBm	0.02 V
1786739144	14 Pkt	-76 dBm	0.02 V
1786738821	7 Pkt	-76 dBm	0.02 V
1786738498	18 Pkt	-76 dBm	0.02 V
1786738173	15 Pkt	-76 dBm	0.02 V
1786737849	5 Pkt	-75 dBm	0.02 V
1786737527	18 Pkt	-75 dBm	0.02 V
1786737201	17 Pkt	-75 dBm	0.02 V
1786736877	14 Pkt	-75 dBm	0.02 V
1786736553	14 Pkt	-75 dBm	0.02 V
1786736231	21 Pkt	-75 dBm	0.02 V
1786735906	7 Pkt	-75 dBm	0.02 V
1786735583	17 Pkt	-75 dBm	0.02 V
1786735259	15 Pkt	-75 dBm	0.02 V
1786734936	18 Pkt	-75 dBm	0.02 V
1786734612	13 Pkt	-75 dBm	0.02 V
1786734287	19 Pkt	-75 dBm	0.02 V
1786733964	14 Pkt	-75 dBm	0.02 V
1786733640	21 Pkt	-75 dBm	0.02 V
1786733316	15 Pkt	-75 dBm	0.02 V
1786732992	14 Pkt	-75 dBm	0.02 V
1786732669	20 Pkt	-75 dBm	0.02 V
1786732345	17 Pkt	-75 dBm	0.02 V
1786732020	18 Pkt	-75 dBm	0.02 V
1786731696	13 Pkt	-76 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)