APRS Track Direct

My position About ☰

reset

ED1ZAP-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAP-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V.BAT*	C.LOAD*	TEMP*	V.PLS*
1778033633	12.4 V	1.29 A	12 C	12.4 V
1778032733	12.4 V	1.61 A	12 C	12.4 V
1778031832	12.4 V	1.53 A	12 C	12.4 V
1778030931	12.4 V	2.5 A	12 C	12.4 V
1778030030	12.5 V	1.29 A	12.5 C	12.4 V
1778029129	12.5 V	1.53 A	12.5 C	12.4 V
1778028228	12.5 V	1.45 A	12.5 C	12.4 V
1778027328	12.5 V	1.77 A	12.5 C	12.4 V
1778026427	12.5 V	1.37 A	12.5 C	12.4 V
1778025526	12.5 V	1.61 A	12.5 C	12.4 V
1778024625	12.5 V	1.45 A	13 C	12.4 V
1778023725	12.5 V	1.69 A	13 C	12.4 V
1778022823	12.5 V	1.29 A	13 C	12.6 V
1778021923	12.5 V	1.61 A	13 C	12.4 V
1778021022	12.5 V	1.53 A	13.5 C	12.6 V
1778020120	12.5 V	1.85 A	13.5 C	12.6 V
1778019220	12.6 V	1.45 A	13.5 C	12.6 V
1778018319	12.6 V	1.77 A	13.5 C	12.6 V
1778017418	12.6 V	2.34 A	13.5 C	12.6 V
1778016520	12.6 V	1.77 A	14 C	12.6 V
1778015616	12.6 V	1.45 A	14 C	12.6 V
1778014715	12.6 V	1.61 A	14 C	12.6 V
1778013814	12.5 V	5.4 A	14.5 C	12.4 V
1778012914	12.5 V	5.48 A	14.5 C	12.4 V
1778012013	12.5 V	5.16 A	14.5 C	12.6 V

*Used Equation Coefficients:

V.BAT: 0, 0.1, 0

C.BAT: 0, 0.0806, 0

C.LOAD: 0, 0.0806, 0

TEMP: 0, 0.5, -64

V.PLS: 0, 0.2, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)