APRS Track Direct

My position About ☰

reset

SR8WXD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	Vbatt*
1836274428	29 Pkt	10 Pkt	1 Pkt	13.28 V
1836274427	29 Pkt	9 Pkt	1 Pkt	13.28 V
1836274277	28 Pkt	4 Pkt	1 Pkt	13.16 V
1774115014	10 Pkt	6 Pkt	0 Pkt	13.32 V
1774114240	13 Pkt	6 Pkt	0 Pkt	13.3 V
1774113468	15 Pkt	10 Pkt	5 Pkt	13.3 V
1774112698	17 Pkt	9 Pkt	4 Pkt	13.3 V
1774111922	24 Pkt	9 Pkt	4 Pkt	13.32 V
1774111152	32 Pkt	8 Pkt	2 Pkt	13.3 V
1774110382	31 Pkt	6 Pkt	0 Pkt	13.26 V
1774109612	25 Pkt	6 Pkt	0 Pkt	13.32 V
1774108842	26 Pkt	12 Pkt	6 Pkt	13.28 V
1774108069	13 Pkt	8 Pkt	2 Pkt	13.32 V
1774107295	15 Pkt	5 Pkt	0 Pkt	13.36 V
1774106526	17 Pkt	5 Pkt	0 Pkt	13.32 V
1774105752	17 Pkt	7 Pkt	1 Pkt	13.26 V
1774104979	21 Pkt	6 Pkt	0 Pkt	13.32 V
1774104205	18 Pkt	6 Pkt	0 Pkt	13.32 V
1774103432	17 Pkt	6 Pkt	0 Pkt	13.32 V
1774102659	14 Pkt	6 Pkt	0 Pkt	13.3 V
1774101887	19 Pkt	5 Pkt	0 Pkt	13.32 V
1774101117	17 Pkt	4 Pkt	0 Pkt	13.32 V
1774100344	13 Pkt	5 Pkt	0 Pkt	13.32 V
1774099574	18 Pkt	6 Pkt	0 Pkt	13.32 V
1774098804	19 Pkt	6 Pkt	0 Pkt	13.3 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)