APRS Track Direct

My position About ☰

reset

DB0PIB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0PIB. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vfm*	Vbuf*	Isol*	Tbat*
1732288605	12.2 V	12.3 V	0 A	5 C
1732288604	12.2 V	12.3 V	0 A	5 C
1732288304	12.3 V	12.3 V	0 A	5 C
1732288007	12.3 V	12.3 V	0 A	5 C
1732288004	12.3 V	12.3 V	0 A	5 C
1732287704	12.3 V	12.3 V	0 A	5 C
1732287410	12.3 V	12.3 V	0 A	5 C
1732287404	12.3 V	12.3 V	0 A	5 C
1732287104	12.3 V	12.3 V	0 A	5 C
1732286808	12.3 V	12.3 V	0 A	5 C
1732286804	12.3 V	12.3 V	0 A	5 C
1732286504	12.3 V	12.4 V	0 A	5 C
1732286211	12.3 V	12.4 V	0 A	5 C
1732286204	12.3 V	12.4 V	0 A	5 C
1732285904	12.3 V	12.4 V	0.2 A	5 C
1732285622	12.3 V	12.4 V	0.39 A	5 C
1732285604	12.3 V	12.4 V	0.39 A	5 C
1732285304	12.3 V	12.4 V	0.2 A	5 C
1732285006	12.3 V	12.4 V	0.2 A	5 C
1732285004	12.3 V	12.4 V	0.2 A	5 C
1732284704	12.3 V	12.4 V	0.2 A	5 C
1732284405	12.3 V	12.4 V	0.2 A	5 C
1732284404	12.3 V	12.4 V	0.2 A	5 C
1732284104	12.3 V	12.4 V	0.39 A	5 C
1732283812	12.3 V	12.4 V	0.2 A	5 C

*Used Equation Coefficients:

Vfm: 0, 0.1, 0

Vbuf: 0, 0.1, 0

Isol: 0, 0.1953, -24.8031

Ievs: 0, 0.1953, -24.8031

Tbat: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)