APRS Track Direct

My position About ☰

reset

VK4KLL-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4KLL-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BATT1*	T1 PL60*	T2 INV*	Rx1h*
1836274830	13.74 Volt	26 C	0 C	110 Pkt
1836274531	13.74 Volt	26 C	0 C	110 Pkt
1836274530	13.74 Volt	26 C	0 C	110 Pkt
1836274380	13.82 Volt	26 C	0 C	100 Pkt
1836274230	13.74 Volt	26 C	0 C	120 Pkt
1836273930	13.74 Volt	26 C	0 C	110 Pkt
1766294033	13.74 Volt	32 C	33 C	120 Pkt
1766293734	13.74 Volt	32 C	33.5 C	100 Pkt
1766293434	13.66 Volt	32 C	33 C	110 Pkt
1766293133	13.66 Volt	32 C	33 C	100 Pkt
1766292834	13.66 Volt	32 C	33 C	90 Pkt
1766292534	13.66 Volt	32 C	33 C	90 Pkt
1766292233	13.66 Volt	32 C	32.5 C	90 Pkt
1766291934	13.66 Volt	32 C	32.5 C	90 Pkt
1766291634	13.66 Volt	32 C	32.5 C	100 Pkt
1766291334	13.74 Volt	32 C	32 C	90 Pkt
1766291034	13.74 Volt	32.5 C	32 C	90 Pkt
1766290734	13.74 Volt	32.5 C	32 C	80 Pkt
1766290434	13.74 Volt	32.5 C	32 C	80 Pkt
1766290134	13.66 Volt	32.5 C	32.5 C	70 Pkt
1766289835	13.66 Volt	32.5 C	32.5 C	70 Pkt
1766289834	13.66 Volt	32.5 C	32.5 C	70 Pkt
1766289534	13.66 Volt	32.5 C	32.5 C	70 Pkt
1766289234	13.66 Volt	32.5 C	32.5 C	80 Pkt
1766288934	13.66 Volt	32.5 C	32.5 C	80 Pkt

*Used Equation Coefficients:

BATT1: 0, 0.079, -0.8

T1 PL60: 0, 0.5, -64

T2 INV: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)