APRS Track Direct

My position About ☰

reset

YB2WB-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB2WB-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1762269181	0 Pkt	-67 dBm	19.32 V
1762268168	0 Pkt	-67 dBm	19.32 V
1762267155	0 Pkt	-66 dBm	19.34 V
1762266142	0 Pkt	-65 dBm	19.4 V
1762265128	0 Pkt	-66 dBm	19.48 V
1762264115	0 Pkt	-65 dBm	19.5 V
1762263102	1 Pkt	-70 dBm	19.5 V
1762262089	0 Pkt	-69 dBm	19.5 V
1762261076	1 Pkt	-63 dBm	19.46 V
1762260063	0 Pkt	-64 dBm	19.5 V
1762259050	0 Pkt	-65 dBm	19.5 V
1762258037	0 Pkt	-65 dBm	19.5 V
1762257024	1 Pkt	-66 dBm	19.5 V
1762256011	0 Pkt	-65 dBm	19.48 V
1762254998	0 Pkt	-63 dBm	19.48 V
1762253984	0 Pkt	-64 dBm	19.46 V
1762252971	0 Pkt	-65 dBm	19.52 V
1762251958	0 Pkt	-67 dBm	19.79 V
1762250945	1 Pkt	-65 dBm	17.9 V
1762249932	0 Pkt	-65 dBm	19.58 V
1762248919	0 Pkt	-65 dBm	20.61 V
1762247906	0 Pkt	-70 dBm	20.92 V
1762246893	1 Pkt	-69 dBm	20.98 V
1762245880	1 Pkt	-70 dBm	21 V
1762244866	0 Pkt	-70 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)