APRS Track Direct

My position About ☰

reset

KK4YEL-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KK4YEL-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1786723094	88 Pkts	86 Pkts	31 C
1786719494	72 Pkts	70 Pkts	31 C
1786715894	157 Pkts	154 Pkts	32 C
1786712295	374 Pkts	368 Pkts	31 C
1786708695	467 Pkts	461 Pkts	34 C
1786705095	306 Pkts	299 Pkts	35 C
1786701494	389 Pkts	384 Pkts	34 C
1786697894	445 Pkts	441 Pkts	34 C
1786694294	365 Pkts	358 Pkts	34 C
1786690694	333 Pkts	330 Pkts	34 C
1786687094	340 Pkts	335 Pkts	34 C
1786683494	467 Pkts	463 Pkts	34 C
1786679894	445 Pkts	438 Pkts	34 C
1786676294	418 Pkts	414 Pkts	34 C
1786672694	223 Pkts	220 Pkts	34 C
1786669094	379 Pkts	376 Pkts	33 C
1786665494	233 Pkts	230 Pkts	31 C
1786661894	273 Pkts	269 Pkts	31 C
1786658294	217 Pkts	206 Pkts	31 C
1786654694	209 Pkts	204 Pkts	31 C
1786651094	280 Pkts	275 Pkts	30 C
1786647494	281 Pkts	278 Pkts	31 C
1786643894	124 Pkts	114 Pkts	32 C
1786640294	77 Pkts	75 Pkts	32 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)