APRS Track Direct

My position About ☰

reset

TB3BGB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TB3BGB. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274465	0 Pkt	-54 dBm	12.92 V
1836274292	0 Pkt	-54 dBm	12.94 V
1778035268	0 Pkt	-52 dBm	13.29 V
1778034345	0 Pkt	-53 dBm	13.29 V
1778033422	0 Pkt	-53 dBm	13.29 V
1778032499	0 Pkt	-50 dBm	13.29 V
1778031576	1 Pkt	-52 dBm	13.29 V
1778030652	0 Pkt	-52 dBm	13.25 V
1778029728	0 Pkt	-52 dBm	13.29 V
1778028805	0 Pkt	-52 dBm	13.29 V
1778027882	0 Pkt	-53 dBm	13.29 V
1778026958	0 Pkt	-52 dBm	13.29 V
1778026035	2 Pkt	-52 dBm	13.29 V
1778025110	1 Pkt	-53 dBm	13.25 V
1778024186	0 Pkt	-53 dBm	13.29 V
1778023262	0 Pkt	-52 dBm	13.25 V
1778022339	3 Pkt	-53 dBm	13.29 V
1778021413	1 Pkt	-53 dBm	13.29 V
1778020489	0 Pkt	-53 dBm	13.29 V
1778019566	0 Pkt	-53 dBm	13.29 V
1778018643	0 Pkt	-52 dBm	13.25 V
1778017720	0 Pkt	-53 dBm	13.29 V
1778016797	0 Pkt	-53 dBm	13.29 V
1778015875	0 Pkt	-53 dBm	13.29 V
1778014951	1 Pkt	-53 dBm	13.25 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)