APRS Track Direct

My position About ☰

reset

VK2BLS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2BLS-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1762336316	12.22 Volts	20.03 Deg.C
1762335416	12.22 Volts	20.52 Deg.C
1762334515	12.19 Volts	21.01 Deg.C
1762333615	12.22 Volts	21.5 Deg.C
1762332723	12.22 Volts	21.99 Deg.C
1762331813	12.22 Volts	22.48 Deg.C
1762330912	12.22 Volts	23.45 Deg.C
1762330011	12.22 Volts	25.41 Deg.C
1762328209	12.22 Volts	25.41 Deg.C
1762327308	12.22 Volts	26.39 Deg.C
1762326407	12.25 Volts	26.88 Deg.C
1762325505	12.22 Volts	27.85 Deg.C
1762320095	12.36 Volts	30.3 Deg.C
1762319193	12.25 Volts	30.3 Deg.C
1762311977	12.28 Volts	29.81 Deg.C
1762307468	12.31 Volts	27.85 Deg.C
1762306566	12.31 Volts	27.37 Deg.C
1762304763	12.34 Volts	27.37 Deg.C
1762302961	13.33 Volts	28.83 Deg.C
1762302904	13.33 Volts	28.34 Deg.C
1762302867	13.24 Volts	27.85 Deg.C
1762302208	12.34 Volts	26.88 Deg.C
1762300232	13.33 Volts	27.85 Deg.C
1762300136	13.24 Volts	27.37 Deg.C
1762299960	13.21 Volts	27.37 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -283.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)