APRS Track Direct

My position About ☰

reset

LW3HBV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LW3HBV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1749327765	0 Pkt	-2 dBm	12.26 V
1749326843	0 Pkt	-4 dBm	12.26 V
1749325921	0 Pkt	-2 dBm	12.26 V
1749324999	0 Pkt	-2 dBm	12.26 V
1749324077	0 Pkt	-2 dBm	12.26 V
1749323155	0 Pkt	-2 dBm	12.26 V
1749322233	0 Pkt	-2 dBm	12.24 V
1749321311	0 Pkt	-2 dBm	12.26 V
1749320389	0 Pkt	-2 dBm	12.26 V
1749319467	0 Pkt	-2 dBm	12.26 V
1749318545	0 Pkt	-2 dBm	12.26 V
1749317623	0 Pkt	0 dBm	12.26 V
1749316701	0 Pkt	-2 dBm	12.24 V
1749315779	0 Pkt	-3 dBm	12.26 V
1749314857	0 Pkt	-3 dBm	12.26 V
1749313935	0 Pkt	-2 dBm	12.26 V
1749313013	0 Pkt	-2 dBm	12.26 V
1749312091	4 Pkt	-2 dBm	12.26 V
1749311169	9 Pkt	-2 dBm	12.26 V
1749310247	1 Pkt	-2 dBm	12.26 V
1749309325	0 Pkt	-1 dBm	12.26 V
1749308403	0 Pkt	0 dBm	12.24 V
1749307481	0 Pkt	-2 dBm	12.26 V
1749306559	0 Pkt	-2 dBm	12.26 V
1749305637	0 Pkt	-2 dBm	12.26 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)