APRS Track Direct

My position About ☰

reset

OM3KFF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OM3KFF-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CpuTemp*	Load1*	Uptime*	RX*	TX*
1790675513	56 degC	0.84	18.6 d	6 pkt	0 pkt
1790674913	56 degC	0.04	18.6 d	17 pkt	0 pkt
1790674309	55.5 degC	0.12	18.6 d	11 pkt	1 pkt
1790673710	56 degC	0.66	18.6 d	23 pkt	1 pkt
1790673110	56 degC	0.08	18.6 d	20 pkt	0 pkt
1790672514	56 degC	0.12	18.6 d	27 pkt	0 pkt
1790671913	56 degC	0.66	18.6 d	2 pkt	0 pkt
1790671313	56.5 degC	0.56	18.6 d	15 pkt	0 pkt
1790670710	56.5 degC	0.08	18.6 d	12 pkt	1 pkt
1790670110	56.5 degC	0.22	18.6 d	24 pkt	1 pkt
1790669510	55.5 degC	0.01	18.6 d	28 pkt	0 pkt
1790668913	56 degC	0	18.5 d	19 pkt	1 pkt
1790668314	56.5 degC	0.06	18.5 d	13 pkt	2 pkt
1790667713	56.5 degC	0.05	18.5 d	13 pkt	0 pkt
1790667110	56.5 degC	0.24	18.5 d	18 pkt	1 pkt
1790666509	56 degC	0.76	18.5 d	22 pkt	1 pkt
1790665910	56 degC	0.02	18.5 d	12 pkt	0 pkt
1790665313	56 degC	0.02	18.5 d	27 pkt	0 pkt
1790664714	56 degC	0.38	18.5 d	18 pkt	0 pkt
1790664114	56 degC	0.4	18.5 d	32 pkt	0 pkt
1790663510	56 degC	0.91	18.5 d	22 pkt	1 pkt
1790662909	56 degC	0.71	18.5 d	30 pkt	1 pkt
1790662310	56 degC	0.14	18.5 d	25 pkt	0 pkt
1790661713	56 degC	0.02	18.5 d	33 pkt	0 pkt
1790661114	56 degC	0.34	18.5 d	30 pkt	0 pkt

*Used Equation Coefficients:

CpuTemp: 0, 0.5, 0

Load1: 0, 0.01, 0

Uptime: 0, 0.1, 0

RX: 0, 1, 0

TX: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)