APRS Track Direct

My position About ☰

reset

VK2HFG-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2HFG-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Battery*	CPU*	Tx*
1770138385	12.6 Volts	51 DegC	20 pkts
1770134784	12.6 Volts	52 DegC	21 pkts
1770131184	12.5 Volts	52 DegC	21 pkts
1770127585	12.7 Volts	52 DegC	17 pkts
1770123985	12.5 Volts	54 DegC	22 pkts
1770120384	12.6 Volts	54 DegC	23 pkts
1770116784	12.7 Volts	56 DegC	23 pkts
1770113184	12.7 Volts	58 DegC	24 pkts
1770109584	12.8 Volts	60 DegC	26 pkts
1770105984	12.8 Volts	63 DegC	28 pkts
1770102384	12.9 Volts	67 DegC	32 pkts
1770098784	13.8 Volts	67 DegC	28 pkts
1770095184	13.7 Volts	69 DegC	29 pkts
1770091585	14 Volts	71 DegC	26 pkts
1770087985	13.8 Volts	70 DegC	95 pkts
1770086981	13.7 Volts	70 DegC	12 pkts
1770085618	13.8 Volts	67 DegC	35 pkts
1770082018	14 Volts	62 DegC	37 pkts
1770078418	13.7 Volts	58 DegC	39 pkts
1770074819	13.7 Volts	54 DegC	32 pkts
1770071218	13.2 Volts	52 DegC	53 pkts
1770067618	13.2 Volts	48 DegC	35 pkts
1770064019	12.5 Volts	46 DegC	36 pkts
1770060418	12.3 Volts	47 DegC	35 pkts
1770056818	12.4 Volts	47 DegC	29 pkts

*Used Equation Coefficients:

Battery: 0, 0.1, 0

CPU: 0, 1, 0

Tx: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)