This is the latest recevied telemetry packets stored in our database for station/object SP2HCA-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1836274607 | 233 Count | 446 Count | 152 Count | 4.15 VDC | 0.14 VDC |
| 1766227357 | 73 Count | 718 Count | 46 Count | 0 VDC | 0 VDC |
| 1766226154 | 68 Count | 654 Count | 42 Count | 0 VDC | 0 VDC |
| 1766224965 | 54 Count | 596 Count | 33 Count | 0 VDC | 0 VDC |
| 1766222566 | 47 Count | 501 Count | 28 Count | 0 VDC | 0 VDC |
| 1766221363 | 43 Count | 458 Count | 25 Count | 0 VDC | 0 VDC |
| 1766218963 | 33 Count | 349 Count | 17 Count | 0 VDC | 0 VDC |
| 1766216560 | 28 Count | 296 Count | 14 Count | 0 VDC | 0 VDC |
| 1766215362 | 26 Count | 269 Count | 13 Count | 0 VDC | 0 VDC |
| 1766212958 | 20 Count | 193 Count | 9 Count | 0 VDC | 0 VDC |
| 1766211757 | 18 Count | 171 Count | 8 Count | 0 VDC | 0 VDC |
| 1766210559 | 16 Count | 143 Count | 7 Count | 0 VDC | 0 VDC |
| 1766209358 | 13 Count | 113 Count | 5 Count | 0 VDC | 0 VDC |
| 1766206957 | 8 Count | 52 Count | 2 Count | 0 VDC | 0 VDC |
| 1766205756 | 5 Count | 25 Count | 0 Count | 0 VDC | 0 VDC |
| 1766203365 | 112 Count | 975 Count | 81 Count | 0 VDC | 0 VDC |
| 1766202167 | 110 Count | 946 Count | 80 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)