APRS Track Direct

My position About ☰

reset

BV8SI-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV8SI-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1836274708	35 C	143 p	143 p	143 p	44927 p
1774121649	19 C	143 p	143 p	143 p	218562 p
1774120450	18 C	143 p	143 p	143 p	218557 p
1774119249	18 C	143 p	143 p	143 p	218548 p
1774118049	18 C	143 p	143 p	143 p	218538 p
1774116849	19 C	143 p	143 p	143 p	218529 p
1774115650	18 C	143 p	143 p	143 p	218522 p
1774114450	19 C	143 p	143 p	143 p	218515 p
1774113250	20 C	143 p	143 p	143 p	218507 p
1774112050	18 C	143 p	143 p	143 p	218499 p
1774110849	18 C	143 p	143 p	143 p	218492 p
1774109650	19 C	143 p	143 p	143 p	218484 p
1774108451	18 C	143 p	143 p	143 p	218476 p
1774107250	18 C	143 p	143 p	143 p	218469 p
1774106050	18 C	143 p	143 p	143 p	218458 p
1774104850	19 C	143 p	143 p	143 p	218448 p
1774103650	19 C	143 p	143 p	143 p	218442 p
1774102451	20 C	143 p	143 p	143 p	218435 p
1774101250	20 C	143 p	143 p	143 p	218413 p
1774100051	19 C	143 p	143 p	143 p	218407 p
1774098850	19 C	143 p	143 p	143 p	218400 p
1774097650	19 C	143 p	143 p	143 p	218392 p
1774096450	18 C	143 p	143 p	143 p	218385 p
1774095250	19 C	143 p	143 p	143 p	218377 p
1774094050	19 C	143 p	143 p	143 p	218337 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)